CSA Z662-07 UPD 2
|
ID： |
59304B5785E649C8ABBFCE0028734CD1 |
|
文件大小(MB)： |
0.16 |
|
页数： |
10 |
|
文件格式： |
|
|
日期： |
2011-3-27 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
Update No. 2*,to CSA Z662-07 Package,August 2008,Note: General Instructions for CSA Standards are now called Updates. Please contact CSA Information Products,Sales or visit www.ShopCSA.ca for information about the CSA Standards Update Service.,The CSA Z662-07 Package consists of,?Z662-07, Oil and gas pipeline systems — originally published June 2007; and,?Z662.1-07, Commentary on CSA Z662-07, Oil and gas pipeline systems — originally published June 2007.,*Update No. 1 (August 2008) to CSA Z662-07 Package consists of replacement pages for CSA Z662-07.,Update No. 2 (August 2008) to CSA Z662-07 Package consists of replacement pages for CSA Z662.1-07.,Revisions issued: Update No. 1 to CSA Z662-07 Package — August 2008,If you are missing any updates, please contact CSA Information Products Sales or visit www.ShopCSA.ca.,The following revisions have been formally approved and are marked by the symbol delta (Δ) in the margin,on the attached replacement pages:,CSA Z662.1-07 originally consisted of 240 pages (xiv preliminary and 226 text), each dated June 2007.,It now consists of the following pages:,?Update your copy by inserting these revised pages.,?Keep the pages you remove for reference.,Revised Z662.1-07: Contents and Commentary on Clauses 4.22, 14.3.9.1 and 14.3.9.2,and Table 5.1,New None,Deleted None,June 2007 v–xiv, 1–46, 49–52, 55–192, and 195–226,August 2008 iii, iv, 47, 48, 53, 54, 193, and 194,Contents,. Canadian Standards Association Commentary on CSA Z662-07, Oil and gas pipeline systems,August 2008,Preface xv,0 Introduction 1,1 Scope 2,2 Reference publications 5,3 Definitions 14,4 Design 17,4.1 General 17,4.2 Design conditions 17,4.2.2 Temperature 17,4.3 Design criteria 18,4.3.2 Class location assessment areas 18,4.3.4 Class location end boundaries 24,4.3.5 Pressure design for steel pipe — General 33,4.3.6 Pressure design for steel pipe — Design factor (F) 34,4.3.7 Pressure design for steel pipe — Location factor (L) and Table 4.2, Location factor for steel pipe 34,4.3.8 Pressure design for steel pipe — Joint factor (J) and Table 4.3, Joint factor for steel pipe 36,4.3.9 Pressure design for steel pipe — Temperature factor (T) and Table 4.4, Temperature factor for steel,pipe 36,4.3.11 Pressure design for steel pipe — Wall thickness 37,4.3.12 Pressure design for components — General 37,4.3.13 Pressure design for components — Closures 38,4.3.18 Pressure design for components — Welded branch connections 39,4.3.19 Pressure design for components — Reinforcement of single openings 39,4.4 Valve location and spacing 39,4.5.1 Buttwelded joints 40,4.5.4 Additional requirements for mechanical interference fit joints 40,4.6.5 Hoop stress 40,4.11 Cover and clearance 40,4.12 Crossings 41,4.12.1 General 41,4.12.2 Crossings of utilities 42,4.12.3 Crossings of roads and railways 42,4.13 Requirements for pipelines in proximity to electrical transmission lines and associated facilities 42,4.13.1 General 42,4.13.2 Effects on pipelines in proximity to high-voltage dc lines 43,4.14 Design of compressor stations over 750 kW and pump stations over 375 kW 43,4.14.2 Design of compressor stations over 750 kW 43,4.14.3 Design of pump stations over 375 kW 43,4.15 Liquid storage in oil pipeline pump stations, tank farms, and terminals 45,4.15.1 Aboveground tanks over 4000 L 45,4.15.2 Aboveground tanks of 4000 L or less 45,4.15.3 Underground tanks 46,4.15.4 Pressure spheres, bullets, and ancillary vessels 46,4.16 Gas storage in pipe-type and bottle-type holders 46,4.16.2 Aboveground installations 46,4.18 Pressure control and overpressure protection of piping 46,(Replaces p. iii, June 2007) iii,Z662.1-07 . Canadian Standards Association,August 2008,4.18.1 General 47,4.18.2 General design requirements for systems for pressure control and overpressure protection 47,4.18.3 Additional design requirements for pressure-relieving installations 47,4.18.4 Additional overpressure-protection requirements for compressor and pump stations 47,4.19 Instrument, control, and sampling pipe 47,4.20 Leak detection capability 47,4.21 Odorization 48,4.22 Requirements for pipelines installed by horizontal directional drilling 48,5 Materials 48,5.1 Qualification of materials 48,5.2 Steel materials and gaskets 49,5.2.1 Design temperatures — Steel materials 49,5.2.2 Notch toughness requirements — Steel pipe 49,5.2.3 Notch toughness requirements — Steel components 55,5.2.4 Steel pipe 56,5.2.5 Steel components — General 57,5.2.6 Steel components — Flanges 57,5.2.7 Steel components — Bolting 58,5.2.8 Steel components — Gaskets 58,5.2.9 Steel components — Fittings 59,5.3 Other materials 60,5.3.1 Aluminum piping 60,5.3.2 Polyethy……
……